- Flexible digital patchbay
- Format Converter
- 16x16 ch Audio interface
- Seamless DAW integration with Integrator plug-in
- Unique digital matrix style UI for direct selection of signals
- 8 ch of sample rate conversion on board for optimal digital adaptation
- Analog outs (phone and balanced line) for monitoring
- Scene recall enabling instant recall of full setups
- Front panel UI lock to prevent unintended use
- JET™ technology ensures rock solid digital signal handling
Tired of re-wiring over and over again? With Konnekt Digital x32 you connect your digital hardware once, make the wiring that fits your setup requirements and you’re good to go. All subsequent routing takes place from the front panel of Digital Konnekt x32.
Digital Konnekt x32 provides efficient format conversion between units using ADAT, SPDIF, TOS and AES/EBU digital formats. Any input format can be converted into either of the listed formats and aligned to any sample rate ranging from 44.1 to 96 kHz.
Two FireWire connections enable you to use Konnekt Digital x32 as an audio interface connected to a computer. It streams 16 channels of audio to and from the computer, and is compatible with other TC Electronic audio interfaces.
Unique digital matrix style UI for direct selection of signals
Digital Konnekt x32’s Integrator plug-in makes integration of external hardware into your DAW environment seamless. It offers a “plug-in” audio routing representation of your external hardware, e.g. Reverb4000, Finalizer, System6000, etc.
Since Integrator operates like a normal VST/AU plug-in it can be inserted on any track, as a send effect or on the master output of your host application.
Since all functions are assigned individual front panel buttons without underlying sub menus, Digital Konnekt x32 gives an instant overview of routing and offers intuitive and direct monitoring and operation.
|8 ch of sample rate conversion on board for optimal digital adaption|
In a digital setup without a sample rate converter it is imperative that all units run by the same sample rate. Increasingly more project studios prefer to run their host application at 96 kHz, a sample rate which lots of digital hardware doesn’t support. Also, using devices that does not receive a digital signal - keyboards, synthesizers, cd/dvd players etc., is a challenge without sample rate converters.
With Digital Konnekt x32 this is no problem. Its sample rate converters allow you to align units running at different sample rates ranging from 44.1 kHz to 96 kHz.
|Analog outs (phone and balanced line) for monitoring|
Analog stereo outs allow you to connect a set of monitor speakers. This is perfect when you use it as an audio interface, and together with the phones out, it easily lets you monitor each of the inputs individually.
JET™ technology ensures rock solid digital signal handling
|Scene recall enabling instant recall of full setups|
The Scene recall function allows you to store up to 4 snapshots of all active routings and settings.
The TC developed DICE II chip, running Digital Konnekt x32’s super stable clock, is based on JET™, Jitter Elimination Technology. With the integrated JET™ technology the DICE II chip is able to align all digital signals from external digital sources with extreme perfection. The great benefit of this is that all supported digital formats will be automatically aligned and thereby you get maximum digital quality through and through.
8x AES/SPDIF IO/6x TOS IN, 4x TOS OUT
8x ADAT (up to 96 kHz SMUX) IO
16 channels FireWire IO
Word Clock IO
Analog stereo out + headphone out
The Integrator plug-in (VST and AU) makes integration of external hardware into your DAW environment seamless. It offers a “plug-in” audio routing representation of your external hardware, e.g. Reverb4000, Finalizer, System6000, etc.
VST and AUSince Integrator operates like a normal VST/AU plug-in it can be inserted on any track, as a send effect or on the master output of your host application.
Multiple devicesIntegrator works with up to four konnekt audio interfaces at a time, so if you have more interfaces, simply select the one that the external hardware is attached to.
Easy routingTo setup the routing of Integrator is as simple as possible. You only have to select the first audio channel: Integrator will then figure out how to route the rest. So, if you for instance have connected your external hardware to the S/PDIF 7+8, simply select S/PDIF 7.
CalibrationWith the calibrate feature you can measure the latency of the entire signal chain from plug-in input to plug-in output, including the latency of the plug-in, the audio driver, the D/A and A/D converters and the latency of the external hardware you use. You can see the total roundtrip latency, and the host application will automatically compensate for this latency. Integrator has sample accurate latency measurement.
Test signalIntegrator is able to generate a test signal to verify that your external hardware is routed correctly. The auto test signal mode will cycle between channels.
MetersIntegrator features nice and clear send and return meter sections, and with the level controls you can control the send level and the return level individually.
Included with all konnekt audio interfacesFrom TC Near konnekt software version 1.30, the Integrator plug-in is included with all konnekt interfaces.
Minimum system requirements
Mac OSX 10.4.9 or later
• PowerPC (1 GHz or faster) or Intel CPU
• 512 MB RAM
• FireWire (IEEE 1394) port*
• OS X 10.4.9 or later
Windows XP SP2 or Vista x32
• Pentium 4, 1.6 GHz or faster
• 512 MB RAM
• FireWire (IEEE 1394) port*
• Windows XP
* We recommend running konnekts on a dedicated FireWire bus.
If your computer has one or more FireWire connections on the chassis they will typically run on the same FireWire bus. You may connect the konnekt to one of these. If you intend to run more FireWire devices simultaneously, such as e.g. an external hard drive, we recommend running this device on a separate bus.
This would typically be on an installed FireWire PCI card. Note that such a FireWire PCI card typically has 3 ports but these also operate on a single bus.
** Please beware that not all functionality is available at quad speed sample rates (176.4 & 192 kHz)
Submit the form below to get notified with the latest exciting Product News and Great Competitions
PowerCore owners have two more reasons to celebrate as TC Electronic is giving away two incredible reverb and compression plug-ins for the award-winning platform!
Radar Loudness Meter for Native DAWs
LM6 Radar Loudness Meter gives you direct access to our revolutionary meter whether you are using Media Composer, Final Cut Pro X, Pro Tools, Logic Pro, Nuendo, Wavelab, Sequoia, etc. on a Mac or PC and whether your productions are in mono, stereo or 5.1.
to find a TC Electronic dealer near you
PowerCore 4.3.3 for PC and 4.3.3 or MAC
TC Electronic has released PowerCore 4.3.3. Version 4.3.3 improves performance and stability
DJ Greg Stainer
Most residents of Dubai know of DJ Greg Stainer from Radio 1 UAE and many more know of him as resident DJ at Zinc, the nightclub at Crowne Plaza Hotel. An important part of his hardware arsenal is the TC Electronic Konnekt 24D, a firewire audio interface with built-in DSP effects.