Triple C single

Triple C single

For technical specification and support, please visit our public website

Schematics	PCB layout	Part list
Front P16503-3	Front P16501-3
Mainboard P16001-4	Mainboard P16001-4
Mainboard P16001-6	Mainboard P16001-6
		Service Partlist Front Overview partlist
Service-notes
Noise in Delay algorithm due to fault in DRAM timing
Serrated washer on earth connections
Manhattan repair hints
Software
Please refer to our public webpage for latest software version
How to upload
GUIDES
Sound check
Self test menu
Performance data

Conditions: In level: 0dB*, Out level: 0dB, Analog in 48KHz, Digital in gain 0dB, Input RNG, Output RNG 20dB, Bypass all ON.

Generator:		DUT notes:	Audio Precision analyzer setup:
				Result
Muted: L			Noise	<-76	dBu	un-wtd 22-22k
Muted: R			Noise	<-76	dBu	un-wtd 22-22k
23	dBu, 2kHz		THD+N	<0.003	%	un-wtd 22-22k
			@ Level	+ 20	dBu	+/-	dB
23	dBu, 2kHz		THD+N	<0.003	%	un-wtd 22-22k
			@ Level	+20	dBu	+/-	dB
24	dBu, 2kHz		THD+N	<0.070	%	un-wtd 22-22k
			@ Level	+0.0	dBu	0.5	dB
24	dBu, 20Hz	+/- 1dB	Level	+20	dBu	rel. 1kHz
24	dBu, 20kHz	+/- 1dB	Level	+20	dBu	rel. 1kHz

24	dBu, 1kHz		Level	+20	dBu	1	dB
			Level		dBFS		dB

Enter the self test menu.

Power on while pressing "ENVELOPE MODE / SOFTLIM".
Loop the midi in/out with a midi cable.
Choose "Front test" by pressing "MENU" and run through the test procedure.
Power off and on.

Connections:

Connect the power cable.
Connect pedal jack to EXTERNAL CONTROL IN.
Connect the MIDI OUT to MIDI IN and MIDI THRU to MIDI IN in the panel.
Connect DI(S/PDIF) to Fin96-controllers DUT-stik and DO(S/PDIF) to the Fin96(DI) in the panel.
Connect the MAIN OUT to "Input 1" in the panel. The MAIN IN connects to "Output 1" in the panel NOTE: Do not connect the SIDE HAIN IN AND DIRECT OUT.
Adjust the Finalizer 96 like this: Input:S/PDIF Mode: Mode48 Fin96-controller set to "CD dig out".

In/Out test:

Connect a CD player to the unit listen if there is a signal playing through the device.
Check if the device locks to the 44.1khz and check if the in and output matches with the Fin96.
Press the pedal jack and see/hear if the bypass goes on and off and if the MIDI LED in the panel does blink.
Disconnect the MIDI IN or the MIDI OUT.
Press the MENU button and choose I/O and choose Digital and press MENU. Check if the signal locks to the Fin96 listen to the signal at all levels and listen for any bad sound. Repeat for Analog test.
Change between 48khz and 44.1khz and notice if the Fin96 locks to it and listen too any bad sound.

Noise Check:

Pause the CD player.
Set the INPUT and the MAKE UP GAIN level to max. You can hear a weak click sound when passing the +6dB on the INPUT pot meter.
Check the pot meter for high noise and crackling sounds if so the pot meter may be defect.
Adjust the INPUT and the MAKE UP GAIN to low settings and start the CD player.

Finishing up:

Enter the self test menu
Enter the front test and follow the procedure make sure all is working ok.
Feed a signal through the unit and knock test it, listen for any sound changes, click or noise sounds.
Power off and on a couple of times to ensure it starts up properly every time and check if the latest software is installed.
Finish