| |
PERFORMANCE DATAConditions: In level: 0dB*, Out level: 0dB, Analog in 48KHz, Digital in gain 0dB, Input RNG, Output RNG 20dB, Bypass all ON. Generator: | DUT notes: | Audio Precision analyzer setup: | | | | | Result | | | Muted: L | | Noise | | <-76 | dBu | un-wtd 22-22k | Muted: R | | Noise | | <-76 | dBu | un-wtd 22-22k | 23 | dBu, 2kHz | | THD+N | | <0.003 | % | un-wtd 22-22k | | | | @ Level | | + 20 | dBu | +/- | dB | 23 | dBu, 2kHz | | THD+N | | <0.003 | % | un-wtd 22-22k | | | | @ Level | | +20 | dBu | +/- | dB | 24 | dBu, 2kHz | | THD+N | | <0.070 | % | un-wtd 22-22k | | | | @ Level | | +0.0 | dBu | 0.5 | dB | 24 | dBu, 20Hz | +/- 1dB | Level | | +20 | dBu | rel. 1kHz | 24 | dBu, 20kHz | +/- 1dB | Level | | +20 | dBu | rel. 1kHz | | | | | | | | | 24 | dBu, 1kHz | | Level | | +20 | dBu | 1 | dB | | | | Level | | | dBFS | | dB |
Self test menu Power on while pressing "LEVELS + RECALL". - Loop the midi in/out with a midi cable.
Choose "Front test" by pressing "HARMNOY MUTE" and run through the test procedure. Power OFF and ON.
Reset the unit: Power on the unit while pressing "HARMONY MUTE"to enter the system menu. - Choose "Reset system parameters" press "HARMONY MUTE" and wait until its done.
- Find the latest software and upload it (Midi speed set to 31250).
- Power OFF the unit.
Connect the power cable. Connect pedal jack to EXTERNAL CONTROL IN. Connect the MIDI OUT to MIDI IN and MIDI THRU to MIDI IN in the panel. Connect DO(S/PDIF) to Fin96-controller. Connect Analog IN/OUT cables. Finalizer96 settings: Input:S/PDIF Mode: Mode48 Fin96-controller set to "CD dig out". Connect a microphone(phantom power) to the Mic input.
Connect a CD player to the unit and play a dry vocal track and listen for a proper output signal. Check if the device locks to the 44.1khz and check if the in and output matches with the Fin96. Press the pedal jack and see/hear if the bypass goes ON and OFF and if the MIDI LED in the panel does blink. Disconnect the MIDI IN or the MIDI OUT. Press the "SETUP" button and set the "INPUT" to "Digital" and press "MENU". Check if the signal locks to the Fin96 listen to the signal at all levels and listen for any bad sound. Repeat for Analog test. Change between 48khz and 44.1khz and notice if the Fin96 locks to it and if sounds normal. Control that the microphone works properly with and without the phantom power. Check if the -20dB works while singing in the microphone the signal should drop.
Pause the CD player. Set the "INPUT LEVEL" to max output. You can hear a weak click sound when passing the approx.12 o'clock on the "INPUT" potmeter. Check the potmeter for high noise and crackling sounds the pot meter may be defect. Set the "INPUT LEVEL" to low output and start the CD player.
- Enter the self test menu
- Enter the front test follow the procedure make sure all is working ok.
- Feed a signal through the unit and knock test it, listen for any sound changes, click or noise sounds.
- Power OFF and ON a couple of times to ensure it starts up properly every time and check if the latest software is installed.
- Finish
|
|
